Atwood Bolt Swivel Jacks
Atwood Bolt Swivel Jacks are designed to allow the jack tube to
swing easily from its horizontal transit position to the vertical
stationery position, locking securely into place with a solid
1/2" diameter spring-loaded pin. The bolt design of the swivel
holds the jack firmly against the mounting bracket, substantially
reducing the side-to-side wobble while in use and virtually
eliminates the annoying chatter during travel. The jacks are
available in both weld-on and bolt-on versions that will fit all
rectangular frames up to 3" wide and 3, 4, or 5 inches deep.
Atwood Retaining Ring Swivel Jacks
Zinc Plated for Marine Applications
Atwood retaining ring swivel jacks have
been designed and tested considering
requirements such as tongue-lifting capacities,
side loading capacities, length of travel
needed to accommodate tractor and other
tow vehicle hitch heights, clearance of
power take-off shafts and jack cycle life necessary
to match equipment usage and life
expectancy.
Mounting Brackets
Brackets, retaining ring, and when applicable,
nuts, bolts and lock washers.
87502 87501
Bolt-on bracket fits
frames 2 or 3" wide
and 3,4, or 5" deep.
Weld-on bracket
fits most frames.
Bulk 25 quantity
Atwood Power Jacks
Atwood Power Jacks make positioning a trailer hassle-free.
The patented design and convenience of push button operation
take the physical exertion out of cranking a trailer up or
down. Simply push the button to quickly and effortlessly raise
or lower the trailer into position with complete control.
The Atwood Power Jack cannot change position until powered,
giving you complete control over jack and trailer movement
at all times. It is ideal for long-term storage, too.
Atwood jacks are not affected by temperature variations,
providing solid, consistent performance regardless of the weather.
Permanently Lubricated
Our low maintenance jacks are carefully designed for
years of convenient, trouble-free use. Manual override
handle included.
Atwood A-Frame Jacks
A-Frame jacks, with triangular
brackets, provide easy bolt-on
or weld-on mounting through
A-Frame couplers and are available
in side and top-wind models.
Casters or feet quickly install
on jack ram. (Casters and feet
must be ordered separately.)
Atwood Couplers
Atwood A-Frame couplers weld onto frame members set at 50° angles and are manufactured
for S.A.E. class 3 and 4. These couplers are designed for demanding applications. They feature a jack mounting hole for easy installation and are available for 2" and 2 5 /16" ball size.
Atwood Hitch Balls
Atwood Mobile Products offers
a variety of 2" and 2 5 /16" companion
hitch balls to meet trailer
towing applications from
5,000 to 40,000 lbs. gross vehicle
weight. Forged or machined
using high-strength fatigue-resistant
steel, Atwood hitch
balls are designed to mate with
specific Atwood couplers for
optimal fit, long life and trouble-free
performance.
Each Atwood hitch ball comes
complete with a lock washer
and hex nut for quick, secure
installation, and meets all
applicable S.A.E. and D.O.T.
standards.
Atwood Pro Stands
Atwood’s NEW Pro Standsis the
ideal answer for jacks with casters that
have to be set on soft ground, surfaces
that are not level or will be left in place
for long periods of time.The large base
easily supports the jack, caster and trailer.
The high profile Pro Stand
is great for between use
storage where the
boat can be left in
a tilted position to
allow it to drain.
Atwood Casters and Feet
Atwood casters and jack feet,
with convenient “twist-lock”,
provide easy attachment to
the jack and quick removal
for towing. They mount on
all Atwood A-Frame jacks.
